Programmers

Programmers are hardware devices that are used to transfer the application software from your PC into the Microcontroller. Some programmers are low cost but support only a limited number of microcontrollers, others are expansive and have a wide range. Apart from that there is no difference in the programming method or quality.
Sort By:  
PCB JDM In Circuit Programming for PIC
NOTE: Use C828 transistors on place on 2N3906 as labelled on silk screen. JDM programmer is the simplest programmer for microchip PIC Microcontrollers. This PCB works well with almost all commonly used PIC microcontrollers by the hobbyists. It gives out 5V output so should be used with 5V tolerant microcontrollers. A number of client software are available, we prefer using PICPGM which is free to download. JDM programmers work with serial port, and preferably the hardware type RS232 serial port as provided in desktop computers. We have not tested it with USB to RS232 converters.
PKR 25.00
ST LINK V2 PROGRAMMER FOR STM8 STM32

PRODUCT DESCRIPTION

Mini ST-LINK V2, fully consistent with the official version, support for automatic upgrades, support the full range STM32 SWD (only 4pins including SWCLK, SWDIO, and power) and a full range STM8 SWIM (only 4pins including SWIM, Reset and power) download and debug. 

FEATURES:

  • PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable!
  • Interface definition directly marked on the shell, clear, convenient and practical!
  • 5V, 3.3V offers in the same time, allowing you to program your target board with both 5V and 3.3V
  • Shell characters using laser engraving, never fade off! Permanent clarity!
  • 500MA internal resettable fuse, complete protection of your expensive computer motherboard!
  • Red and blue color LED indicator, allowing you to always observe ST-LINK V2 working condition!
  • With 4 DuPont line, so you can easily respond to different target board line order!
  • Use anti-static bag packaging.

SUPPORTS FOR ST-LINK V2:

  • ST-LINK Utility 2.0 and above
  • STVD 4.2.1 and above
  • STVP 3.2.3 and above
  • IAR EWARM V6.20 and above
  • IAR EWSTM8 V1.30 and above
  • KEIL RVMDK V4.21 and above
PKR 300.00
USBasp Programmer for AVR Microcontroller

These AVR programmers are based on Thomas Fischl’s USBasp design and connect to your computer’s USB port. Not only are they quite compact (70x20mm), but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done in firmware.

Being an Open source hardware (OSHW) project, released under the GNU General Public License, you are free to download the schematic and firmware from Thomas’s website, but then you have a chicken and egg problem. In order to load the USBASP firmware onto the atmega8 on the programmer, yes you guessed it, you need an AVR programmer. Much easier to buy one fully built and programmed.

Some of the features include:

  • Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
  • Support for Windows, Mac OS X and Linux (will work on Windows 8.1)
  • 5 KB/sec maximum write speed
  • Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
  • 10 pin ISP interface (conforms to standard ISP 10-pin pinout)

The latest Window Drivers are fully signed, so you can use them on Windows Vista and above without any issues. The driver will work on both 32 and 64 bit platforms. On Linux And Mac OS X no kernel driver is required, just use AVRdude and specify the correct port.

The programmer will work with a wide variety of Atmel AVR microcontrollers including the Atmega8a and Atmega168a. A full list is available on the specifications tab. The programmer will also work with a variety of software including

PKR 350.00
PIC Programmer JDM Type In Circuit
This is the simplest and cheapest programmer possible for Microchip PIC Microcongtrollers. Design is open source and available by the name of JDM. This programmer works on PC serial port, it may not work wit USB to Serial adapters. It needs physical RS232 type serial port on PC. Client software are available, we prefer to use PIC PGM software to transfer hex files int the microcontroller using this.
PKR 250.00
Microchip PICKit-3 Programmer Debugger
  • USB (Full speed 12 Mbits/s interface to host PC)
  • Real-time execution
  • Firmware upgradeable from PC/web download
  • Supports low voltage to 2.0 volts (2.0 V to 6.0 V range)
  • Diagnostic LEDs (power, busy, error)
  • Read/write program and data memory of microcontroller
  • Erase of program memory space with verification
  • Program up to 512 K byte flash with the Programmer-to-Go
PKR 1,800.00
PKR 2,000.00
PICKit-2 Clone Microchip Programmer Debugger
PICKit-2 is a product of Microchip, the manufactures of PIC Microcontrollers. This product is however open source and has all the rights for making the product clones.

This clone is good for programming 5V tolerant Microchip PIC Microcontrollers, we have not tested it with 3.3V MCUs. The programmer has ZIF socket, to use it as a standalone programmer.

It is programmer as well as runtime debugger, to stop and debug the MCU while its running in its environment.
PKR 2,000.00
Per Page      1 - 6 of 6
  • 1