Microchip PIC

Sort By:  
PCB Microchip PIC Lab-1 Trainer Board
DIY project, make your own Microchip PIC Trainer Board
Features:
  • Microchip PIC 18 pin Microcontroller 16,F84A,16F628A,16F648A,16F819,16F88 (16F819 Recommended)
  • 20MHz clock oscillator (detachable from IO lines)
  • In Circuit Serial Programming header (PICKit-2, PICKit-3 Compatible)
  • Character LCD Interface (HD44780) 16x2 and 16X4 all supported (Contrast is provided by a fixed 1.5K resistor)
  • 4 individually accessible status LEds
  • One darlington transistor (TIP122) for heavy DC Loads (Relay, motor,solenoid etc)
  • 3 momentary push switches
  • RS232 compliant USART Serial port with MAX232
  • Infrared remote control sensor
  • two pre-conditioned analog inputs with potentiometers (to scale down input volts) with 5V zener diodes protection
  • On Board 5V1.5A voltage regulator
  • All IO lines available as headers for extension to external circuits.
  • All devices can be individually connected to microcotroller pins
PKR 75.00
PCB Microchip PIC Lab-2 Trainer Board PIC18F2550 USB
PCB Only. for PIC Lab-II PCB Supports:
Features:
  • Support for all Microchip PIC 28 Pin Microcontrollers (Pin Compatible with PIC18F2550)
  • 20MHz Clock crystal (Can run at 48MHz with Fuse settings of MCU)
  • Character LCD (HD44780 Interface)
  • 3 momentary Push switches (Pulled up)
  • Reset Switch
  • One potentiometer with zener diode protection for conditioned Analog Input
  • One Preamplifier with a gain of 100 for amplifying weak analog signals.
  • Lowpass filter circuit for two PWM channels with OPAMP as voltage follower to give clean analog output with some power to drive.
  • 38KHz IR Remote control sensor
  • One SPDT Relay (Note drive circuit is not isolated, so do not use for high AC Voltage)
  • DS1307 Realtime clock with battery I2C
  • 244C16 EEPROM I2C (You can replace with anyother EEPROM of the same family)
  • One status LED
  • In Circuit Serial Programming header (PICKit-2 and PICKit-3 compatible)
  • On Board 5V 1.5A Power regulator
  • All devices can be selected or deselected from IO Lines through convenient DIP Switches
  • All IO Lines available through headers organized into PORTS, along with 5V Supply for easy interfacing with external boards.
  • Power source selectable as USB or External adapter
PKR 100.00
PCB Easy PIC Trainer Board
THis PCB allows you to make your own Microchip PIC trainer board. The board supports all 18 pin Microchip PIC Microcontrollers.
  • Onboard 5V regulator
  • 18 pin Microchip PIC MCU
  • RS232 communication
  • 4 LEDs
  • 2 push switches
  • IR Remote sensor (Both center + and Center -)
  • LM35 temperature sensor
  • character LCD
  • Buzzer
  • on board 5V power regulator
PKR 35.00
PIC Lab II
Microchip PIC Lab-2 Trainer Board PIC18F2550 USB
  • Microchip is one of the largest microcontrollers manufacturers in the world. It has a wide spectrum of microcontrollers ranging from 8 to 32 bits. All families are compatible in common peripherals they share. Learning one makes it easy to migrate to others.
    This board has been designed from the point of view of a hobbyist who wants to learn as well as expand his microcontroller skills. The board has most of the commonly used external circuits fabricated, so that you just need to enable them and use. In case you want to use something else, IO line headers are available for easy interfacing with external modules and circuits.
    The board has USB-B connector that can power the board, as well as used to program the device. PIC18F2550 has built-in USB 2.0 module, this board contains a USB bootloader into PIC18F2550 that allows direct programming without any external programmer.

    Features:
  • Support for all Microchip PIC 28 Pin Microcontrollers (Pin Compatible with PIC18F2550)
  • 20MHz Clock crystal (Can run at 48MHz with Fuse settings of MCU)
  • Character LCD (HD44780 Interface)
  • 3 momentary Push switches (Pulled up)
  • Reset Switch
  • One potentiometer with zener diode protection for conditioned Analog Input
  • One Preamplifier with a gain of 100 for amplifying weak analog signals.
  • Lowpass filter circuit for two PWM channels with OPAMP as voltage follower to give clean analog output with some power to drive.
  • 38KHz IR Remote control sensor
  • One SPDT Relay (Note drive circuit is not isolated, so do not use for high AC Voltage)
  • DS1307 Realtime clock with battery I2C
  • 244C16 EEPROM I2C (You can replace with anyother EEPROM of the same family)
  • One status LED
  • In Circuit Serial Programming header (PICKit-2 and PICKit-3 compatible)
  • On Board 5V 1.5A Power regulator
  • All devices can be selected or deselected from IO Lines through convenient DIP Switches
  • All IO Lines available through headers organized into PORTS, along with 5V Supply for easy interfacing with external boards.
  • Power source selectable as USB or External adapter

PKR 500.00
Microchip PIC Lab-3 Development Board Strawberry USB
Microchip is one of the largest microcontrollers manufacturers in the world. It has a wide spectrum of microcontrollers ranging from 8 to 32 bits. All families are compatible in common peripherals they share. Learning one makes it easy to migrate to others.This board has been designed specifically for the PIC18F4550 microcontroller, however it is generic in form and can be used with any other 40 Pin, pin compatible Microchip PIC Microcontrollers.The board has major circuitry and IO lines for interfacing with external modules and circuits.
Features:
  • Support for All 40 Pin Microchip PIC Microcontrollers (PIC18F4550 Recommended)
  • 20MHz Crystal oscillator (MCU can be configured to 48MHz using internal fuse settings)
  • One Momentary Push switch (Pulled Up)
  • Two status LEDs
  • Reset Button
  • In Circuit Serial Programming Header (PICKit-2 and PICKit-3 Compatible)
  • On board 5V 1.5A Regulator
  • 24C16 External EEPROM I2C (can be replaced with any other of family)
  • Supplied DC Power is available through T-Block for use in external circuits
  • All IO Lines of MCU are available through headers organized into PORTS along with 5V DC Supply for easy interfacing
  • On board devices, including USB lines can be connected or disconnected from the MCU pins using simple DIP Switch.
  • Can be powered from USB or External source
  • PIC18F4550 comes with pre-loaded USB Bootloader so that you can program it directly without external programmer.
PKR 300.00
PIC Lab-1
Microchip PIC Lab-1 Trainer Board
Microchip is one of the largest microcontrollers manufacturers in the world. It has a wide spectrum of microcontrollers ranging from 8 to 32 bits. All families are compatible in common peripherals they share. Learning one makes it easy to migrate to others.
This board is based upon 18 pin, 8 bit PIC microcntrollers, there are a number of compatible PIC 18 pin microcontrollers that are supported by this board. The board has reconfigurable host of peripheral devices that students and hobbyists can configure and connect to microcontroller pins of their choice. The board needs an external programmer.

Features:
  • Microchip PIC 18 pin Microcontroller 16,F84A,16F628A,16F648A,16F819,16F88 (16F819 Recommended)
  • 20MHz clock oscillator (detachable from IO lines)
  • In Circuit Serial Programming header (PICKit-2, PICKit-3 Compatible)
  • Character LCD Interface (HD44780) 16x2 and 16X4 all supported
  • 4 individually accessible status LEds
  • One darlington transistor (TIP122) for heavy DC Loads (Relay, motor,solenoid etc)
  • 3 momentary push switches
  • RS232 compliant USART Serial port with MAX232
  • Infrared remote control sensor
  • two pre-conditioned analog inputs with potentiometers (to scale down input volts) with 5V zener diodes protection
  • On Board 5V1.5A voltage regulator
  • All IO lines available as headers for extension to external circuits.
  • All devices can be individually connected to microcotroller pins

PKR 250.00
PIC Board for 28 Pin MCU Beetle Board
Bare board for 28 pin Microchip PIC microcontrollers. Ideal for PIC18F2550, that has built-in USB 2.0 interface. The board has USB-B connector that can be used to power as well as program the PIC18F2550 (using our USB bootloader). For others all IO lines and power lines are available as 0.1" header that can be plugged into the breadboard easily. It can be used with other 28 pin PIC microcontrollers. Contains 20MHz oscillator as well as a reset switch.
PKR 150.00
Per Page      1 - 8 of 8
  • 1