DIY Kits

Sort By:  
PCB L293D
PCB L293D Dual H-Bridge Motor Driver
PCB for L293D Dual H-Bridge motor driver IC
PKR 20.00
PCB Microchip PIC Lab-1 Trainer Board
DIY project, make your own Microchip PIC Trainer Board
Features:
  • Microchip PIC 18 pin Microcontroller 16,F84A,16F628A,16F648A,16F819,16F88 (16F819 Recommended)
  • 20MHz clock oscillator (detachable from IO lines)
  • In Circuit Serial Programming header (PICKit-2, PICKit-3 Compatible)
  • Character LCD Interface (HD44780) 16x2 and 16X4 all supported (Contrast is provided by a fixed 1.5K resistor)
  • 4 individually accessible status LEds
  • One darlington transistor (TIP122) for heavy DC Loads (Relay, motor,solenoid etc)
  • 3 momentary push switches
  • RS232 compliant USART Serial port with MAX232
  • Infrared remote control sensor
  • two pre-conditioned analog inputs with potentiometers (to scale down input volts) with 5V zener diodes protection
  • On Board 5V1.5A voltage regulator
  • All IO lines available as headers for extension to external circuits.
  • All devices can be individually connected to microcotroller pins
PKR 75.00
PCB Microchip PIC Lab-2 Trainer Board PIC18F2550 USB
PCB Only. for PIC Lab-II PCB Supports:
Features:
  • Support for all Microchip PIC 28 Pin Microcontrollers (Pin Compatible with PIC18F2550)
  • 20MHz Clock crystal (Can run at 48MHz with Fuse settings of MCU)
  • Character LCD (HD44780 Interface)
  • 3 momentary Push switches (Pulled up)
  • Reset Switch
  • One potentiometer with zener diode protection for conditioned Analog Input
  • One Preamplifier with a gain of 100 for amplifying weak analog signals.
  • Lowpass filter circuit for two PWM channels with OPAMP as voltage follower to give clean analog output with some power to drive.
  • 38KHz IR Remote control sensor
  • One SPDT Relay (Note drive circuit is not isolated, so do not use for high AC Voltage)
  • DS1307 Realtime clock with battery I2C
  • 244C16 EEPROM I2C (You can replace with anyother EEPROM of the same family)
  • One status LED
  • In Circuit Serial Programming header (PICKit-2 and PICKit-3 compatible)
  • On Board 5V 1.5A Power regulator
  • All devices can be selected or deselected from IO Lines through convenient DIP Switches
  • All IO Lines available through headers organized into PORTS, along with 5V Supply for easy interfacing with external boards.
  • Power source selectable as USB or External adapter
PKR 100.00
PCB Easy PIC Trainer Board
THis PCB allows you to make your own Microchip PIC trainer board. The board supports all 18 pin Microchip PIC Microcontrollers.
  • Onboard 5V regulator
  • 18 pin Microchip PIC MCU
  • RS232 communication
  • 4 LEDs
  • 2 push switches
  • IR Remote sensor (Both center + and Center -)
  • LM35 temperature sensor
  • character LCD
  • Buzzer
  • on board 5V power regulator
PKR 35.00
PCB JDM In Circuit Programming for PIC
NOTE: Use C828 transistors on place on 2N3906 as labelled on silk screen. JDM programmer is the simplest programmer for microchip PIC Microcontrollers. This PCB works well with almost all commonly used PIC microcontrollers by the hobbyists. It gives out 5V output so should be used with 5V tolerant microcontrollers. A number of client software are available, we prefer using PICPGM which is free to download. JDM programmers work with serial port, and preferably the hardware type RS232 serial port as provided in desktop computers. We have not tested it with USB to RS232 converters.
PKR 25.00
Per Page      1 - 5 of 5
  • 1