Arduino

Sort By:  
Arduino UNO R3 SMD ATmega328P | With Cable
Standard Arduino UNO R3, ATmega328P DIP with USB Cable
PKR 450.00
NodeMCU LoLin ESP8266 Developement Board
NodeMCU LoLin ESP8266 Developement Board - USB Chip CH340.

An open-source firmware and development kit that helps you to prototype your IOT product within a few Lua script lines.

The Module is based on ESP-12/ESP8266 WiFi Module by AI thinker. Module integrates 3.3V Regulator, GPIO, PWM, IIC, 1-Wire and ADC all in one board.

The default firmware for this board is the NodeMCU firmware, which is a LUA interpreter. A user application can be stored in the Flash ROM in the form of a LUA script.

[!] Note: The user may need to install / update LUA interpreter by himself/herself.

Features

  • Based on ESP-12E ESP8266 wifi board
  • All I/Os output
  • No need to press reset/flash for pgoramming
  • Lolin NodeMCU V3 version has CH340 USB-TTL converter
  • Larger current support
  • Supports windows 7/8/10 by CH340, and supports ESPlorer

Documents and Downloads

  • NodeMCU Support page
  • To Flash NodeMCU board find related content here
  • NodeMCU Github link
PKR 400.00
Arduino UNO R3 ATmega328P | With Cable
Standard Arduino UNO R3, ATmega328P DIP with USB Cable
PKR 750.00
Multifunction shield
  • 4 digit 7-segment LED display module (3641BH) driven by two serial 74HC595’s (Pin Latch 4, Clock 7, Data 8)

  • 4 Red LEDs (Pin 10,11,12,13) [D1-13, D2-12, D3-11,D4-10]

  • 10K potentiometer (Pin A0) [Vr-A0]

  • 3 x push buttons (Pin A1, A2, A3) [S1-A1, S2-A2, S3-A3]

  • Piezo buzzer (Pin 3 digital ON/OFF) [LS1-3]

  • DS18B20 temperature sensor interface (not included) (Pin A4) [U5-18b20-LM35-A4]

  • Infrared receiver interface (Pin 2) [U4-IR-2] Compatible to a 1838B Infrared IR receiver

  • Bluetooth interface (GND, +5v, 0 = tx, 1 = rx) [APC220]

  • Free pins pwm (5, 6, 9, A5) with GND, +5V

  • Serial interface header for connection to (optional) serial modules (Bluetooth, wireless interface, voice module, a voice recognition module)

    https://www.biomaker.org/multifunction-shield-v2

PKR 950.00
CNC Shield V4 Expansion Board For Arduino Nano
This expansion board as a driver expansion board, can be used for engraving machines, 3D printers. It is a total of three slots, can drive three A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. Very convenient to use.
PKR 300.00
Arduino UNO R3 Proto Shield Kit with Mini Breadboard
Arduino Uno Proto Shield gives possibility to carry your Arduino projects from breadboard and turn them into a proper circuit and also use your specially designed circuits with Arduino.
You can use proto shield without soldering. By a Mini Breadboard you placed on middle section you can do prototyping and tests without dealing with soldering. Proto Shield provides easy usage by carrying all Arduino pins to upper layer. Also there places on proto shield for surface mount devices (SMD). Therefore you can use that type of materials as well.
Arduino Uno Proto Shield has R3 pin sequence and there is a reset button on board. All headers and connectors are sent soldered.
PKR 200.00
Arduino Mega 2560 | With Cable
Standard Arduino Mega 2560, ATmega 2560 With USB Cable
PKR 1,400.00
WeMos D1 WiFi UNO Development Board Based ESP8266 For Arduino
The UNO Based ESP8266 Nodemcu Development Board in the form of the Arduino UNO board format. This WeMos D1 R1 board is compatible with the Arduino IDE and with NodeMCU. The board is controlled by the ESP8266 chip (a 32-Bit processor) and has a larger flash memory compared to an Arduino Uno. It consists of 11 digital I/O pins and 1 analog (input) pin. the board can be connected using a Micro-B type USB cable.
PKR 500.00
NodeMCU LoLin ESP8266 | CP2102 USB
The All-new CP2102 NodeMcu v2 ESP8266 Lua ESP8266 WIFI Development Board IoT Development Board is a fast leading edge low-cost WiFi technology. Modern high-level mature LUA based technology. It is an integrated unit with all available resources on board. It is super simple to complement your existing Arduino projects or any development board that has I/O pins available.

NodeMcu v2 features:

  1. 11 b/g/n Wi-Fi Direct (P2P), soft-AP
  2. Integrated TCP/IP protocol stack
  3. Use CH340G to replace the CP2102.
  4. Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled
  5. Arduino-like hardware IO
  6. Integrated low power 32-bit CPU
  7. Advanced API for hardware IO, which can dramatically reduce the redundant work for configuring and manipulating hardware.
  8. Code like Arduino, but interactively in Lua script.
  9. Nodejs style network API
  10. Event-driven API for network applications,
  11. which facilitates developers writing code running on a 5mm*5mm sized MCU in Nodejs style.
  12. Greatly speed up your IOT application developing process.
  13. Lowest cost WI-FI
  14. Less than WI-FI MCU ESP8266 integrated and easy to prototyping development kit.
  15. We provide the best platform for IoT application development at the lowest cost.
  16. Integrated TR switch, balun, LNA, power amplifier and matching network
  17. Integrated PLL, regulators, DCXO and power management units
  18. Onboard USB to serial chip to easily program and upload codes from the Arduino IDE
  19. Embeds logic level converter circuits
  20. Has onboard 3.3V regulator to ensure enough power to function as your go-to WiFi chip!
  21. Easy access to the GPIO pins for easy prototyping
  22. Easy to use breadboard friendly form factor
  23. Voltage Regulator / Converter, excellent DC to DC conversion, super-efficient
PKR 450.00
Wroom ESP32 Development Kit | 32 Bits

ESP32 developement board with WiFi and Bluetooth support

Built around ESP32-WROOM-32, this minimum system development board achieves optimal performance with its rich peripheral set, Wi-Fi and Bluetooth connectivity offered by our flagship SoC, ESP32. The limit is your imagination!

ESP32-DevKitC contains the entire basic support circuitry for ESP32-WROOM-32, including a USB-UART bridge (CP2102), reset- and boot-mode buttons, an LDO regulator and a micro-USB connector. Every important GPIO is available to the developer.


Documents and Useful Links:
PKR 1,200.00
Arduino Nano V3 with USB Cable
Standard Arduino Nano R3, ATmega328P With USB Cable
PKR 450.00
Arduino Nano V3
Standard Arduino Nano R3, ATmega328P DIP without USB Cable and soldered headers
PKR 350.00
Per Page      1 - 13 of 13
  • 1